Description

Features

- Low noise preamplifier (0.74 nV/√(Hz))
- High gain up to +89 dB
- Switchable analog filters
- Support fast TGC (time gain compensation)
- 2 analog signal inputs PE and TT
- Input attenuator (-20dB)
- Input Impedance 50 Ohm, 10pF
- 10bit A/D Converter
- 100MHz sampling frequency, 8bit sample
- Up to 512k x 16bit samples memory
- Delay settings up to 65535 sample periods
- various triggering mode
- Data transfer speed - up to 132MB/s
- Expansion Connector for extra functions daughter-board
- interfaces (RS232, RS485, SPI, I2C)
- Standard PCI short card (174.63mm x 106.68mm)
- BNC or Lemo analog connectors
- DB15 connector for I/O and power lines
- weight: 175g

Technical Data

Analog parameters:
Input Amplifier Gain: -31dB to 65dB (step 1dB, error +/- 0.3dB)
Input Post-Amplifier: off or +24dB
Input Attenuator: off or -20dB
Input Range: +/- 275mV
(+/-2.5V with Attenuator active)
Full Bandwidth: 0.5 MHz - 25 MHz (-3dB) Switchable Filters(-3dB): 0.5 - 6MHz,0.5 - 10MHz, 0.5 - 15MHz, 0.5 - 25MHz, 1 - 6MHz, 1 - 10MHz, 1 - 15MHz, 1 - 25MHz, 2 - 6MHz, 2 - 10MHz, 2 - 15MHz, 2 - 25MHz, 4 - 6MHz, 4 - 10MHz, 4 - 15MHz, 4 - 25MHz

Pulser:
Pulse Voltage off(0V) to 360V (positive pulse, Short circuit step pulser)
Charging Time regulated from 0 to 3.1us in 0.1us steps
Fall Time <= 20 ns
Pulse Duration Short circuit, bandwidth up to about 50MHz
Output impedance < 1 Ohm

Technical Data

Data processing:
Resolution 10 bit (8bit stored)
Sampling Frequency(MHz) 100; 50; 33,3; 25; 20; 16,7; 14,3; 12,5,
11,1; 10; 9,1, 8,3; 7,7; 7,14 and 6,67
Data Buffer from 1 to 262088 (256k) samples in step of 4
Delay Time Post trigger from 0 to 65535 sample periods in step of 1
PRF up to 20 000 with multiplexers up to 100 000 
Hardware data processing: Absolute, RF
Hardware averaging
Hardware digital filtering

DAC (TGC) with arbitrary waveform generator:
Frequency: 100MHz
Resolution: 8 bit
Max. gain changing: 48dB pro step

Trigger:
On-board trigger timer;
Application trigger rate Software controlled;
External trigger 2x inputs, TTL Signal.
Trigger output signal, TTL Signal

Counters / Input for incremental encoder:
Counters for Incremental Encoders 2 channel, 32-bit

Inputs / Outputs

Transducer connectors:
PE (sending&receiving) BNC or Lemo  TT (receiving only) BNC or Lemo

DB15 connector:
Inputs:
6 inputs
including encoder and external trigger inputs;
Outputs:
6 outputs, including Trigger output signal (Sync Out).

Others:
+12V, -12V fused (polymer fuse) supply for powering external devices,

+5V or Vreg (0-10V) fused (polymer fuse) output for control/supply external device.

PCI Connector:
PCI rev2.2, 32bit, 33MHz, 132MB/s max transfer bandwidth
Universal connector for 3.3V or 5V PCI sockets.

Expansion connector:
2x10pin 2.54mm connector for special functions daughter-boards
+12V, -12V, +5V, +3.3V power pins;
I/O pins serial interfaces (3.3V signal levels): RS232, SPI, I2C and others;
Inputs for general purpose counters;
Interrupt input;
Analog input for A/D converter